Support Forum

ok, so i did a distribution upgrade of Ubuntu Server 12.04 --> Ubuntu Server 12.10... sorry I got antsy. I know that's risky, but I just got to the point where I was ready to reformat the damn thing despite the fact that I have a lot of custom stuff implemented that I don't even know how I did it an...

at 9:18PM, memory usage was at 1518MB. with the use_pickle enabled, but it wasn't downloading the whole time. Just set article caching to 0, RAM is at V=2862M R=667M never got around to removing yenc. what will that do? also, out of curiosity what does use_pickle do? I would like to be able to use a...

Yes, downloads are completing. Even the ones that say joining at 36000% are complete after a reboot or service restart.

I just enabled use_pickle, and restarted the service from the gui.

at 2:52PM CST, sabnzbd gui reads memory usage as: V=3104M R=937M

Now I have 2.6 gigs of ram used. It is raising at a slow and steady pace.

Upon rebooting, I'm watching the Ram info at the top left of sabnzbd, and it is going up like 2MB/sec... I double checked my article cache limit, and I do have it set to 1G, but I have 8 gig of ram and the system only uses about 5-700mb without sabnzbd running, so I thought that was reasonable. I le...

Just reproduced the issue on a totally different nzb, "joining at 36000%" sysload and ram usage off the charts. I'm going to reboot and post my +debug logs in here.

shypike wrote:To what size did you set the article cache in Config->General?

800M to reduce IOPS since it writes directly to a MDADM raid5

I am already examining jobs with zero files still going and I'm close to a solution. When you have jobs hanging which still have files left, it's more likely that it has to do with stalling servers. Can you see in the Status page if there are still connections with servers? i will check that out th...

Checked it again this morning, and the system was basically frozen with massive RAM usage again. I can't even get into the web interface to see what's going on. I'm going to reboot again when I get home and post some logs here.

Alright, so I had to reboot the entire computer because it was lagged down so hard I could barely type commands into the terminal over ssh. After everything came back up, the job that was giving the weirdness looks complete, and the queue is going again... sooo WTF. I'm pretty sure there's a bug her...

79.7% of your 8GB memory? That's impressive indeed. If you stop SAB 0.7.4 and run SAB 0.7.3 on the same queue, does or doesn't it happen? Yeah, it's using a majority of the swap as well! The sysload from memory leak was so high that everything I tried to do took almost 5 minutes, which is really ba...

Also, I've got these warnings: 2012-10-29 00:06:32,533 ERROR: [29/Oct/2012:00:06:32] Traceback (most recent call last): File "/usr/share/sabnzbdplus/cherrypy/_cpwsgi.py", line 79, in setapp s, h, b = self.get_response() File "/usr/share/sabnzbdplus/cherrypy/_cpwsgi.py", line 219,...

Is one job blocking the queue? Have you looked at the job that should finish? When you click on the job, you'll get the list of remaining files. Are there any? What is the "only get articles from the top of the queue" setting? It should be off. One job is not blocking the queue right now,...

I think I may have found a memory leak:



iotop shows low filesystem utilization across the board:

http://img.ctrlv.in/508e0d819a382.jpg system is nearly unresponsive. I'm going to try to restart sabnzbd and see what that does, if that doesn't work i'll try a system reboot. Man... this version of sabnzbd is giving me all kinds of grief. Version: 0.7.4 OS: ubuntu server 12.04 Install-type: reposi...